To download article.UDK 621.81
DOI: 10.15507/2658-4123.030.202001.076-091
Ensuring Reliable Operation of Machine Parts with a New System of Variable Tolerances
Viatcheslav A. Denisov
Head of Scientific Direction “Ensuring the Reliability of Agricultural Machinery”, Federal Scientific Agroengineering Center VIM (5, 1st Institutskiy Proyezd, Moscow 109428, Russia), D.Sc. (Engineering), Professor, Researcher ID: T-4062-2018, ORCID: https://orcid.org/0000-0002-3245-394X, This email address is being protected from spambots. You need JavaScript enabled to view it.
Aleksey A. Solomashkin
Leading Specialist of Federal Scientific Agroengineering Center VIM (5, 1st Institutskiy Proyezd, Moscow 109428, Russia), Researcher ID: Y-8907-2019, ORCID: https://orcid.org/0000-0002-0781-4715, This email address is being protected from spambots. You need JavaScript enabled to view it.
Introduction. The article describes an algorithm for determining the system of tolerances for ensuring reliable operation of parts on the section. The block diagram of the program for determining the variable tolerances is demonstrated. There determined blocks of initial information − broken and smooth curves of the controlled parameter, histogram and graph of resource distribution and definition of active area of control, and blocks of building graphs of “marginal fan curves of wear” and systems of admissions for objects of study of two types: for universal fuel pump (UTN-5) and four-section small-sized fuel pump with mechanical regulator. Two ways of determining the system of tolerances are suggested. Variant 1 is a graphical way through constructing “limit fan curves of wear” and determining tolerances by the value of ordinates in the control points. Variant 2 is an analytical way. There is created a formula to replace the graphical method for determining system tolerances.
Materials and Methods. Two models of high-pressure pump were selected as objects of the study. Nominal and limit values of parameters were known for the pumps. Schedules for checking and equation of wear curves are determined. Dependencies describing the pump plunger pair wear curves are determined. A histogram and graph for determining pump life cycles are drawn. The active area of control is determined with a given failure probability coefficient.
Results. As a result of the study the values for the tolerances system of two types of high pressure fuel pumps are obtained. Reliability values for one pump type are determined. Graphic and analytical algorithms for determining the system of tolerances by the formula are developed.
Discussion and Conclusion. The study approves the possibility of using the variable tolerance as a basis for determining the system of tolerances and reliability indicators of the diagnostic object.
Keywords: system of tolerances, constant tolerance, variable tolerance, reliability indicators, probability of failure, average lifetime
For citation: Denisov V.A., Solomashkin A.A. Ensuring Reliable Operation of Machine Parts with a New System of Variable Tolerances. Inzhenerernyye tekhnologii i sistemy = Engineering Technologies and Systems. 2020; 30(1):76-91. DOI: https://doi.org/10.15507/2658-4123.030.202001.076-091
Contribution of the authors: V. A. Denisov – formulation of the basic research concept, article structure development; A. A. Solomashkin – participation in theoretical and practical research, processing of experimental data, literary and patent analysis, article text development, drawing conclusions.
All authors have read and approved the final manuscript.
Received 10.07.2019; revised 15.10.2019; published online 31.03.2020
REFERENCES
1. Mikhlin V.M., Dorogoy V.N. Determination Method of Details Allowable Wear Ensuring the Improvement of Their Unfailing Performance. Vestnik mashinostroeniya = Russian Engineering Research. 2008; (7):11-14. Available at: https://www.mashin.ru/files/ve708.pdf (accessed 19.02.2020). (In Russ.)
2. Dorogoy V.N. New Method for Determining Permissible Wear on Machine Parts and Connections. Mashinno-tekhnologicheskaya stantsiya – MTS = Machine Technological Station – MTS. 2008; (3):5-10. (In Russ.)
3. Dorogoy V.N., Mikhlin V.M. Algorithm of the Resource-Saving Method for Determining and Assessing Permissible Wear and Tear. Trudy GOSNITI = Works of GOSNITI. 2008; 102:191-194. (In Russ.)
4. Zichenkov M.Ch., Kondakov I.O., Shanygin A.N. Novel Approach to Design of Lightweight and Reliable Composite Primary Aircraft Structures. Nauchnyy vestnik MGTU GA = Civil Aviation High Technologies. 2016; 19(6):127-136. Available at: https://avia.mstuca.ru/jour/article/view/994 (accessed 19.02.2020). (In Russ.)
5. Martyshkin A.P, Maskaykina S.E., Polueshina N.I., et al. Analysis of Machines’ Elements Limit Value Parameter Justification with Derivation of Practical Formula to Find Limit Declination of the Parameter with Given Reliability. Internet-zhurnal “Naukovedenie” = Sociology of Science Internet Journal. 2015; 7(2):109. Available at: https://naukovedenie.ru/PDF/33TVN215.pdf (accessed 19.02.2020). (In Russ.)
6. Solomashkin A.A. Choosing Approximating Functions for Describing Machinery Parts Wear Curve. Mezhdunarodnyy nauchnyy zhurnal = International Scientific Journal. 2011; (4):104-108. (In Russ.)
7. Kazakova V.A., Shinkevich V.A. Corporate Standards: a Driver for Innovative Agribusiness Development. Standarty i kachestvo = Standards and Quality. 2019; (6):52-54. (In Russ.)
8. Kokoreva E.B. The Improved Utilization of Agricultural Machinery. Byulleten nauki i praktiki = Bulletin of Science and Practice. 2018; 4(2):320-325. Available at: https://cyberleninka.ru/article/n/povyshenie-effektivnosti-ispolzovaniya-selskohozyaystvennoy-tehniki (accessed 19.02.2020). (In Russ.)
9. Artemev Yu.N. Methodology for Calculating the Permissible Repair Dimensions and Tensions of Tractor Engines and Couplings. Trudy GOSNITI = Works of GOSNITI. 1994; 4:3-20. (In Russ.)
10. Solomashkin A.А. Strategies for Maintenance and Repair of Machines. Trudy GOSNITI = Works of GOSNITI. 2017; 128:145-151. Available at: http://vimtsm.ru/wp-content/uploads/2019/03/128_2017.pdf (accessed 19.02.2020). (In Russ.)
11. Chernoivanov V.I., Denisov V.A., Solomashkin A.A. An Algorithm for Comparing the Two Systems of Tolerances. Selskokhozyaystvennaya tekhnika: obsluzhivanie i remont = Agricultural Machinery: Maintenance and Repair. 2019; (2):49-54. Available at: https://panor.ru/articles/algoritm-sravneniya-dvukh-sistem-dopuskov/2956.html (accessed 19.02.2020). (In Russ.)
This work is licensed under a Creative Commons Attribution 4.0 License.
