Print

PDF To download article.

DOI: 10.15507/2658-4123.032.202204.520-538

 

Determination of Nominal Dimensions and Permissible Variations in Dimensions of Critical Parts of Foreign Machinery Units

 

Pavel A. Ionov
Head of the Technical Service Machines Chair of Institute of Mechanics and Power Engineering, National Research Mordovia State University (68 Bolshevistskaya St., Saransk 430005, Russian Federation), Cand.Sci. (Engr.), ORCID: https://orcid.org/0000-0001-9794-0071, Researcher ID: S-7146-2018, This email address is being protected from spambots. You need JavaScript enabled to view it.

Petr V. Senin
First Vice-Rector, National Research Mordovia State University (68 Bolshevistskaya St., Saransk 430005, Russian Federation), Dr.Sci. (Engr.), Professor, ORCID: https://orcid.org/0000-0003-3400-7780, Researcher ID: H-1219-2016, This email address is being protected from spambots. You need JavaScript enabled to view it.

Sergey V. Pyanzov
Senior Lecturer of the Technical Service Machines Chair of Institute of Mechanics and Power Engineering, National Research Mordovia State University (68 Bolshevistskaya St., Saransk 430005, Russian Federation), Cand.Sci. (Engr.), ORCID: https://orcid.org/0000-0002-5845-1635, Researcher ID: B-1548-2019, This email address is being protected from spambots. You need JavaScript enabled to view it.

Nikolay V. Rakov
Associate Professor of the Technical Service Machines Chair of Institute of Mechanics and Power Engineering, National Research Mordovia State University (68 Bolshevistskaya St., Saransk 430005, Russian Federation), Cand.Sci. (Engr.), ORCID: https://orcid.org/0000-0003-3687-9371, Researcher ID: ABF-2838-2020, This email address is being protected from spambots. You need JavaScript enabled to view it.

Alexander M. Zemskov
Associate Professor of the Technical Service Machines Chair of Institute of Mechanics and Power Engineering, National Research Mordovia State University (68 Bolshevistskaya St., Saransk 430005, Russian Federation), Cand.Sci. (Engr.), ORCID: https://orcid.org/0000-0002-1489-6077, Researcher ID: S-7748-2018, This email address is being protected from spambots. You need JavaScript enabled to view it.

Abstract 
Introduction. Developing and adapting domestic technologies aimed at the maintenance and repair of foreign equipment is impossible without design documentation. The object of the study was the volumetric hydraulic drive Sauer-Danfoss of 90 series consisting of a hydraulic pump 90R100 and a hydraulic motor 90M100. The purpose of the study is to determine the nominal dimensions and permissible variations in dimensions of critical parts that affect efficiency of the foreign hydraulic drive.
Materials and Methods. The first series of bench tests was devoted to finding the ranges of variation of significant factors influencing the volumetric efficiency. In the second series, there were constructed regression models and by using the steepest ascend method, there were determined the values of critical parts wear and clearances in the critical parts connections affecting efficiency of the hydraulic drive Sauer-Danfoss. The nominal values of dimensions and permissible variations in dimensions of the hydraulic drive critical parts were determined by the dimensional analysis method.
Results. The bench tests made it possible to determine the ranges of changes in critical parts wear and clearances in the critical parts connections of volumetric hydraulic drives that affect the volumetric efficiency. There has been proposed and implemented a comprehensive approach to determining the nominal dimensions and permissible variations in dimensions of critical parts of foreign equipment units. This approach suggests a combination of experimental studies (bench tests) and the method of dimensional analysis. For the new volumetric hydraulic drive Sauer-Danfoss series 90 the following values are received: diameter of a hole in the cylinder block under the piston 22,7+0,006 mm, piston diameter 22,7–0,004 mm, diameter of a hole in the rear cover under the spool 9,5+0,004 mm, spool diameter 9,5–0,0025 mm.
Discussion and Conclusion. There have been determined the nominal values of dimensions, permissible variations in dimensions of critical parts, and the values of technological clearances in the critical parts connections of the new volumetric hydraulic drive Sauer-Danfoss series 90 that affect its efficiency. The results obtained are the basis for the development of technology to restore the efficiency and increase the durability of the volumetric hydraulic drive units of foreign origin.

Keywords: volumetric hydraulic drive, bench tests, efficiency factor, limit state criterion, regression model, dimensional chain

Acknowledgements: The authors express their gratitude to the anonymous reviewers.

Conflict of interest: The authors declare no conflict of interest.

For citation: Ionov P.A., Senin P.V., Pyanzov S.V., et al. Determination of Nominal Dimensions and Permissible Variations in Dimensions of Critical Parts of Foreign Machinery Units. Engineering Technologies and Systems. 2022;32(4):520‒538. doi: https://doi.org/10.15507/2658-4123.032.202204.520-538

Contribution of the authors:
P. A. Ionov – forming the structure of the article, finalizing the initial text, conducting and describing experimental studies, drawing conclusions and conclusions.
P. V. Senin – scientific guidance, analysis and revision of the text.
S. V. Pyanzov – analyzing literature, preparing the text with subsequent revision, conducting and describing experimental studies, optimizing regression models, processing of the obtained results of the study.
N. V. Rakov – analyzing literature, calculating tolerances and limit variations in dimensions of critical parts connections.
A. M. Zemskov – conducting experimental studies.

All authors have read and approved the final manuscript.

Submitted 24.10.2022; approved after reviewing 21.11.2022;
accepted for publication 28.11.2022

 

REFERENCES

1. Ding H., Liu Y., Zhao Ya. A New Hydraulic Synchronous Scheme in Open-Loop Control: LoadSensing Synchronous Control. Measurement and Control. 2020;53(1–2):119–125. doi: https://doi.org/10.1177/0020294019896000

2. Pavlov A.I., Tarbeev A.A., Egorov A.V., et al. Method for Determining the Optimal Operating Time before Replacement of High-Pressure Hoses of Hydraulic Drives of Transport and Technological Machines. Journal of Physics: Conference Series. 2020;1515. doi: https://doi.org/10.1088/1742-6596/1515/4/042065

3. Rylyakin E.G., Semov I.N., Kukharev O.N. The Influence of the Oxidative Polymerization Processes on the Energy Consumption Due to Friction in the Resource Defining Hydraulic Couplings Hydraulic Drive Mate. Research Journal of Pharmaceutical, Biological and Chemical Sciences. 2019;49(1):1064–1069. Available at: https://www.rjpbcs.com/pdf/2019_10(1)/%5B138%5D.pdf (accessed 03.08.2022).

4. Pavlov A.I., Tarbeev A.A., Egorov A.V., et al. Spectral Method for Monitoring the Technical Condition of Hydraulic Drives of Forest Harvester Machines. Journal of Physics: Conference Series. 2020;1515. doi: https://doi.org/10.1088/1742-6596/1515/4/042086

5. Kataev Yu.V., Kostomakhin M.N., Petrishchev N.A., et al. Increasing the Level of Maintenance of Energy-Saturated Equipment. Machinery and Equipment for Rural Area. 2022;(4):27–31. (In Russ., abstract in Eng.) doi: https://doi.org/10.33267/2072-9642-2022-4-27-31

6. Kostomakhin M.N., Kataev Yu.V., Petrishchev N.A., et al. System for Remote Monitoring of Tractors and Detection of Their Incorrect Operation. Russian Engineering Research. 2022;42(4):360–364. (In Russ., abstract in Eng.) doi: https://doi.org/10.3103/S1068798X22040189

7. Pavlov A.I., Tarbeev A.A., Egorov A.V., et al. New Method for Monitoring the Residual Life of High Pressure Hoses. Journal of Physics: Conference Series. 2020;1515. doi: https://doi.org/10.1088/1742-6596/1515/4/042082

8. Shi L., Zhang W., Jiao H., et al. Numerical Simulation and Experimental Study on the Comparison of the Hydraulic Characteristics of an Axial-Flow Pump and a Full Tubular Pump. Renewable Energy. 2020;153:1455–1464. doi: https://doi.org/10.1016/j.renene.2020.02.082

9. Pyanzov S.V., Senin P.V., Ionov P.A., et al. Developing the Test Bench Software for the Technical Inspection of Volumetric Hydraulic Drives. Engineering Technologies and Systems. 2021;31(4):500–517. (In Russ., abstract in Eng.) doi: https://doi.org/10.15507/2658-4123.031.202104.500-517

10. Zhdanko D.A., Gerasimov V.S., Kostomakhin M.N., Petrishchev N.A. Development of Mobile Control Diagnostic Device. Machinery Technical Service. 2021;(1):34–44. (In Russ., abstract in Eng.) doi: https://doi.org/10.22314/2618-8287-2021-59-1-34-44

11. Battarra M., Mucchi E. On the Assessment of Lumped Parameter Models for Gearpump Performance Prediction. Simulation Modelling Practice and Theory. 2019;99:34–40. doi: https://doi. org/10.1016/j.simpat.2019.102008

12. Makarkin I.M., Dankov A.A., Ivleva I.B., et al. Modernization of the Bench KI-28097M-03 to Assess the Quality of Repair of Regulated Hydraulic Units. Selskokhozyaystvennaya tekhnika: obsluzhivanie i remont. 2021;(9):36–41. (In Russ., abstract in Eng.) doi: https://doi.org/10.33920/sel-10-2109-05

13. Pestryakov E.V., Sayapin A.S., Kostomakhin M.N., Petrishchev N. A. Analysis of the Technical Condition of Agricultural Machinery Using Neural Networks. In: Hu Z., Gavriushin S., Petoukhov S., He M. (eds). Advances in Intelligent Systems, Computer Science and Digital Economics III. CSDEIS 2021. Lecture Notes on Data Engineering and Communications Technologies. Vol. 121. Cham: Springer; 2022. doi: https://doi.org/10.1007/978-3-030-97057-4_9

14. Chumakov P.V., Martynov A.V., Kolomeychenko A.V., et al. Evaluation of Technical Condition of Round Gear Hydraulic Pumps of Tractor Mounted Hydraulic Systems. Engineering Technologies and Systems. 2020;30(3):426–447. (In Russ., abstract in Eng.) doi: https://doi.org/10.15507/2658-4123.030.202003.426-447

15. Velichko S.A., Martynova E.G., Ivanov V.I. The Assessment of the Limit State of the Vacuum Piston Type Dough Divider by Oil Consumption. Engineering Technologies and Systems. 2020;30(3):448–463. (In Russ., abstract in Eng.) doi: https://doi.org/10.15507/2658-4123.030.202003.448-463.

16. Kharlamov Yu.A., Zhiltsov A.P., Vishnevsky D.A., Bocharov A.V. Dimensional Analysis of Technological Processes for Reconditioning Machine Parts. BMSTU Journal of Mechanical Engineering. 2021;(5):37–47. (In Russ., abstract in Eng.) doi: https://doi.org/10.18698/0536-1044-2021-5-37-47

17. Polskiy Ye.A., Sorokin S.V. Improving the Reliability of Mechanical Engineering Products by Improving the Precision Analysis of Dimensional Chains. Science Intensive Technologies in Mechanical Engineering. 2022;(6):38–48. (In Russ., abstract in Eng.) doi: https://doi.org/10.30987/2223-4608-2022-6-38-48

18. Frolov V.V. Design Calculation of Dimensional Chains on the Basis of Simulation Modeling. Vestnik of Vitebsk State Technological University. 2019;(2):76–88. (In Russ., abstract in Eng.) doi: https://doi.org/10.24411/2079-7958-2019-13709

19. Khvaschevskaya L.F., Zhuravlev D.A. Analysis of the Accuracy of Machine-Building Рroducts for the Case of Parallel Connected Linear Dimensional Chains. Systems. Methods. Technologies. 2022;(1):48–56. (In Russ., abstract in Eng.) doi: https://doi.org/10.18324/2077-5415-2022-1-48-56

20. Beylin A.B., Tsarfin B.A. Research and Calculation of the Connected Dimensional Chains by the Example of Providing Indicators of Rotaryindexing Tables Accuracy. Izvestiya Samarskogo nauchnogo tsentra Rossiyskoy akademii nauk. 2020;22(3):5–11. (In Russ., abstract in Eng.) doi: https://doi.org/10.37313/1990-5378-2020-22-3-5-11

21. Tamarkin M., Tishchenko E., Murugova E. Design of High Precision Machining Part Processes in Free Abrasives. Smart Innovation, Systems and Technologies. 2022;247:157–167. doi: https://doi.org/10.1007/978-981-16-3844-2_17

22. Mitin E.V., Suldin S.P., Ovchinnikov A.Yu., et al. Determination of the Accuracy Parameters of Machining of a Part by the Graph Method Based on Dimensional Relations. Vestnik mashinostroeniya. 2022;(6):65–71. (In Russ., abstract in Eng.) doi: https://doi.org/10.36652/0042-4633-2022-6-65-71

 

Лицензия Creative Commons
This work is licensed under a Creative Commons Attribution 4.0 License.